Zdroj: www.cni.cz

ČESKÁ TECHNICKÁ NORMA

ICS 83.140.10

Listopad 1998

Světlopropustné profilované plastové
desky pro jednoplášťové střechy -
Část 1: Všeobecné požadavky
a zkušební metody

ČSN
 EN 1013-1

74 7707

 

 

 

Light transmitting profiled plastic sheeting for single skin roofing - Part 1: General requirements and test methods

Plaques profilées éclairantes en  matière plastique pour couverture en simple paroi -  Partie 1: Exigences générales et méthodes d'essai

Lichtdurchlässige profilierte  Platten aus Kunststoff  für einschalige Dacheindeckungen  - Teil 1:  Allgemeine Anforderungen and Prüfverfahren

 

Tato norma přejímá anglickou verzi evropské normy EN 1013-1:1997. Evropská norma EN 1013-1:1997 má status české technické normy.

This standard implements the English version of European Standard EN 1013-1:1997. The European Standard EN 1013-1:1997 has the status of a Czech Standard.

 

© Český normalizační institut, 1998

 

Podle zákona č. 22/1997 Sb. smějí být české technické normy rozmnožovány a rozšiřovány jen se souhlasem Českého normalizačního institutu.




53874


Strana 2

Národní předmluva

 

Citované normy

EN 494 zavedena v ČSN EN 494 Vláknocementové vlnité střešní desky a tvarovky - Technické požadavky a zkušební metody (72 302)

prEN 506 dosud nezavedena

prEN 508-1 dosud nezavedena

prEN 508-2 dosud nezavedena

prEN 508-3 dosud nezavedena

EN 534 dosud nezavedena

prEN 1013-2 dosud nezavedena

EN 1013-3 zavedena v ČSN EN 1013-3 Světlopropustné profilované plastové desky pro jednoplášťové střechy - Část 3: Specifické požadavky a zkušební metody pro desky z polyvinylchloridu (74 7707)

ISO 4892 dosud nezavedena

EN ISO 6603-1 zavedena v ČSN EN ISO 6603-1 Plasty - Stanovení chování tuhých plastů při víceosém rázovém namáhání - Část 1: Metoda padajícího tlouku (64 0628)

 

Vypracování normy

Zpracovatel: Ing. Jana Lorencová, IČO 65428978

Technická normalizační komise: TNK 65 Izolace staveb

Pracovník Českého normalizačního institutu: Ing. Miloslava Syrová


Strana 3

EUROPEAN STANDARD

EN 1013-1

NORME EUROPÉENNE

November 1997

EUROPÄISCHE NORM


 

ICS 83.140.10

 

Descriptors: roofing, plates, ribbed sheets, plastic products, light transmission, specifications, appearance, shock resistance, ageing: materials, dimensional tolerances, tests, measurements, marking

 

English version

 

Light transmitting profiled plastic sheeting for single skin roofing - Part 1: General requirements and test methods

 

Plaques profilées éclairantes en  matière plastique pour couverture en simple paroi -  Partie 1: Exigences générales et méthodes d'essai

Lichtdurchlässige profilierte  Platten aus Kunststoff  für einschalige Dacheindeckungen  - Teil 1:  Allgemeine Anforderungen and Prüfverfahren

 

This European Standard was approved by CEN on 2 November 1997.

 

CEN  members are  bound to  comply with  the CEN/CENELEC  Internal Regulations  which stipulate  the conditions  for giving this European Standard  the status of  a national standard  without any alteration.  Up-to-date lists and  bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.

 

This European  Standard exists in three  official versions (English, French,  German). A version in  any other language made  by translation under the responsibility of a CEN member into its  own language and notified to the Central Secretariat has the same status as the official versions.

 

CEN members are  the national standards bodies of  Austria, Belgium, Czech Republic, Denmark,  Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.

 

3X1.gif

 

EUROPEAN COMMITTEE FOR STANDARDIZATION

COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

 

Central Secretariat: rue de Stassart, 36 B-1050 Brussels

 

_______________

Ó 1997 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members.

Ref. No. EN 1013-1:1997 E


Strana 4

Obsah

 

strana

 

Contents

 

 

 

 

Foreword

2

Introduction

2

1

Scope

2

2

Normative references

3

3

Definitions

4

4

Symbols and abreviations

4

5

Requirements

6

6

Test methods

8

7

Ageing procedure and measurement after ageing (type test)

15

8

Marking, labelling, packaging

18

Annex A (normative): Profile terminology

25

 

Foreword

This European Standard has been prepared by Technical Committee  CEN/TC 128 „Roof covering products for discontinuous laying and products for wall cladding", the secretariat of which is held by IBN.

 

This European  Standard shall be  given the status  of a national  standard, either by  publication of an  identical text or  by endorsement, at the latest by May 1998, and conflicting national standards shall be withdrawn at the latest by May 1998.

 

According to the CEN/CENELEC Internal Regulations, the national  standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.

 

Introduction

 

This Standard describes the general requirements and test methods for transluscent roofing sheets.

 

The  physical properties  of translucent  profiled plastics  sheets differ  from bituminuous,  metal and fibre reinforced cement sheets, as defined in EN 534, prEN 506, prEN 508-1, prEN 508-2, prEN 508-3 or EN 494. They do not necessarily have the same span capabilities and alternative fixing specifications are generally required.

 

Until code of  practices are established, determination of span  capabilities and/or method of fixing is  based on specific test results.

 

Reference  should be  made to  national codes  and/or manufacturer  literature for  requirements concerning  design, storage and installation, including all safety aspects, according to material.

 

1 Scope

 

This European  Standard specifies the  general requirements for  profiled plastics transluscent  sheets for single  skin roofing irrespective of the material used to produce the sheets. The specific requirements according to the material itself are given in specific Parts of this standard, e. g. prEN 1013-2 and EN 1013-3.

 

The standard specifies test methods  and each (excepting that for dimensional tolerances) is defined either  as a type test or a quality  control test.  The test  method for  dimensional tolerances  has been  inctuded to  provide a  common approach  for the purchaser and the


Strana 5

manufacturer in cases of dispute over measurements.

 

This standard is applicable to all types of translucent roofing sheets used in any kind of buildings.

 

NOTE: Material complying with this standard is also applicable for single skin vertical cladding.

 



-- Vynechaný text --

Zdroj: www.cni.cz